Ковани биели Audi за Audi A4 Sedan (8K2, B8) 2.0 TFSI quattro - 211 коня бензин CDNC, CAEB, CPMA - онлайн магазин

ARP 2000 5/16" connecting rod screws in 38.1mm length.

Universally applicable for all H-shank connecting rods.

ARP connecting rod bolts have been developed for the highest requirements and offer optimum safety.

The connecting rod bolts are heat treated and rolled, which gives them up to 10 times higher fatigue strength.

Especially for tuned engines highly recommended!
Connecting rod bearings best to replace directly with.

A 3/8" nut should be used for installation.

More information on the correct tightening of the connecting rod bolts HERE

ARP 5/16 "rod bolts with 38,1mm in length.

Universally applicable for all H-Beam conrods .

ARP custom age 625 + have been developed for the highest requirements and provide optimum safety.

At high engine speed, it arrives at the Aufwertsbewegung the piston to high tensile forces acting on the connecting rod according to Kurbelwellenhub more or less.

To avoid this, a screw is recommended Pleulschraube tear as it has a tensile strength of 260-280 PSI, compared to having only a 2000 ARP Zugfestigkit of 220 PSI

The rod bolts are heat treated and rolled, giving them up to 10 times higher fatigue strength.

Especially for tuned engines highly recommended!

Best exchange directly connecting rod bearings.

(Price for one Bolt.)

More information on how to properly tighten the connecting rod bolts

Optimum piston & connecting rod set for 1.8L TSI engines with chain

This set is optimal for 1.8L TSI engines with chain. Included are high-quality Mahle forged pistons,  ZRP steel conrods I-Beam and ACL racing bearings. With this you can bring your Golf Mk7, Audi TT etc. up to 650 hp on the road without any problems.

All components of this set are perfectly matched to each other and designed for the best racing feeling. Both pistons and connecting rods are extremely light. The pistons provide a smooth engine run and are provided with a special alloy, this makes a small run clearance possible. This enables an optimal power transmission.

The ZRP I-shaft connecting rods are milled from solid material and are extremely crack-resistant and stable due to their construction. In addition, the performance comes to the fore here: With these connecting rods you can drive up to 900 hp. At the same time, they are extremely lightweight. An additional drilling supplies the piston pins with sufficient oil. All in all a super set with which you still save money compared to the single price.

Features of the MAHLE pistons:

• Low running clearance possible thanks to special alloy
• Quiet engine operation even in cold start phase
• High performance piston pin
• Ideal compression ratio and optimum piston shape for TSI engines
• For 1.8L TSI with motor type EA888
• For 148 x 21mm connecting rods
• Low blow-by due to special ring zones
• Anti-Friction Graphite Coating
• Mahle High Performance Piston Rings
• Plug & Play installation possible

 Features of the I-Beam connecting rods:

• high strength milled from solid material
• suitable for extreme performance increases up to approx. 900 hp
• extremely light and very stable
• Magnaflux inspected
• 4 pieces per set
• With ARP 2000 expansion bolts 3/8"
• ARP Assembly lubricant

Features ACL performance bearings:

• Racing bearing
• Coated
• Extra bore for piston pin

Suitable for:

1.8L TSI engines with timing chain as installed in Golf Mk7, Audi TT, Audi A5, Seat Leon and other 1.8L TSI engines.

Engine identification letters: CJSA, CJSB, CABB, CDHB, CJEB, CDAA, DAJA

The specified compression is in conjunction with a cylinder head gasket in series strength.

The figure may vary