Ковани бутала BMW за BMW X1 E84 xDrive 18 d - 136 коня дизел N47 D20 C - онлайн магазин
136 к.с - дизел
03.2009 - 06.2015
-
JE High Performance Piston kit for all BMW M3 E46 and Z4 3.2L S54B32 engines.
Features:
- much lighter
- reinforced
- complete kit with rings and pins
- also for OEM bore size available 87,00mm
- 21mm piston pin diameter
For following BMW E46 and Z4 3.2L engine with engine code S54B32.
The specified compression is based on a 1mm head gasket.
These coatings are not included with this price but can be ordered at JE.
When exceeding 2 Bar boost you need the TURBO piston pins. -
JE High Performance Piston kit for all BMW E36 3L S50B30 engines.
Features:
- much lighter
- reinforced
- complete kit with rings and pins
- also for OEM bore size available 86,00mm
- 21mm piston pin diameter
For following BMW E36 3L engine with engine code S50B30.
The specified compression is based on a 1,83mm head gasket.
These coatings are not included with this price but can be ordered at JE.
When exceeding 2 Bar boost you need the TURBO piston pins. -
JE High Performance Piston kit for all BMW E36 3L S50B30 US engines.
Features:
- much lighter
- reinforced
- complete kit with rings and pins
- also for OEM bore size available 86,00mm
- 22mm piston pin diameter
For following BMW E36 3L engine with engine code S50B30US.
The specified compression is based on a 1,83mm head gasket.
These coatings are not included with this price but can be ordered at JE.
When exceeding 2 Bar boost you need the TURBO piston pins. -
Forged high performance pistons from JE Piston for BMW E36 3.2L S50B32 engines.
Features:
- Extremely lightweight due to special alloy
- Reinforced for maximum performance
- 21mm piston pin
- Complete set incl. piston pin, rings and clips
- Installation and drilling dimensions are included
For BMW E36 3.2L engine with engine code S50B32 and M50B32.
The specified compression is in conjunction with a 1.83mm cylinder head gasket.
Price for a set of JE piston without coating, but this can be specially manufactured by JE for an additional charge.
The special coating can be ordered separately from us. (see below)
Since the series conrods do not withstand a power increase from 300 HP, we recommend to use steel conrods.
From a charge pressure of 2 bar reinforced TURBO piston pins must be used. (see further below) -
JE High Performance Piston kit for BMW 3.0L 24V-Motoren engines with engine code N54B30.
Features:
- much lighter
- reinforced
- complete kit with rings and pins
- 22mm piston pin diameter
- FSR Piston Design
- Also available as new Ultra Series
Since the standard connecting rods cannot withstand an increase in performance from 500 HP, we lead steel connecting rods.
From a boost pressure of 2 bar, TURBO piston pins must be changed. (see further below)
FSR pistons:
The asymmetrical FSR piston line (Forged Side Relief) by JE Pistons includes a modern forged design with a wider piston shirt on the main pressure side and a smaller, friction-reducing shirt on the side pressure side. In combination with precise CNC machining, a high-strength, lightweight piston is created that is extremely durable.Ultra series:
The pistons of the Ultra series combine all premium functions from JE and the brand new technology of the forging industry!
The revolutionary Perfect Skirt coating from JE is one of the many technologically advanced aspects of the Ultra series. It protects the piston shafts, reduces friction and prevents cold start piston shocks and incorrect knocking.
All pistons in the Ultra series are supplied with a ceramic crown coating as standard to ensure a longer service life and better exhaust gas cleaning properties.
Thicker piston pins made of premium material are another feature of the Ultra series.
In combination with the special grain flow-optimized forging technology, the Ultra series is ready for enormous performance. -
JE High Performance Piston kit for BMW 3.0L 24V engines with engine code N55B30.
Features:
- much lighter
- compression 9,5:1
- reinforced
- complete kit with rings and pins
- 22mm piston pin diameter
- FSR Piston Design
- Also available as new Ultra Series
Since the standard connecting rods cannot withstand an increase in performance from 500 HP, we lead steel connecting rods.
From a boost pressure of 2 bar, TURBO piston pins must be changed. (see further below)
FSR pistons:
The asymmetrical FSR piston line (Forged Side Relief) by JE Pistons includes a modern forged design with a wider piston shirt on the main pressure side and a smaller, friction-reducing shirt on the side pressure side. In combination with precise CNC machining, a high-strength, lightweight piston is created that is extremely durable.Ultra series:
The pistons of the Ultra series combine all premium functions from JE and the brand new technology of the forging industry!
The revolutionary Perfect Skirt coating from JE is one of the many technologically advanced aspects of the Ultra series. It protects the piston shafts, reduces friction and prevents cold start piston shocks and incorrect knocking.
All pistons in the Ultra series are supplied with a ceramic crown coating as standard to ensure a longer service life and better exhaust gas cleaning properties.
Thicker piston pins made of premium material are another feature of the Ultra series.
In combination with the special grain flow-optimized forging technology, the Ultra series is ready for enormous performance. -
Forged high-performance pistons from JE Piston for all BMW 3.0L 24V engines with the engine code S55B30, as installed in the M3, M4 and M2 CS
features:
- Extremely light due to special alloy
- Compaction 9.0:1 or 10.3:1
- Reinforced for maximum performance
- 22mm piston pin
- Complete set incl. Piston pin, rings and clips
- Installation and drilling dimensions are included
- FSR design
- Piston skirt extra coated
Special coatings can be ordered separately from us.
Since the Serienpleuel a performance increase from 600 hp not withstand, we recommend to use Stahlpleuel.
From a boost pressure of 2 bar, reinforced TURBO piston pins must be used.
-
MAHLE Motorsport forged pistons for the highest demands!
With the high-performance pistons from MAHLE Motorsport for S85 V10 engines, you can easily reduce compression and achieve more power and durability. A special alloy and special ring zones ensure low running clearance and low blowby. This way you achieve best tuning results and a lot of fun while driving!
Thanks to many years of experience in motorsport, MAHLE is one of the leading manufacturers of high-quality piston.
Features:
- Low running clearance possible thanks to special alloy
- Smooth engine running even in cold start phase
- High-performance piston pin
- Low blowby due to special ring zones
- Anti-friction graphite coating
- Mahle high-performance piston rings
- Extremely light with only approx. 360g per piston
- Plug & Play installation possible
All piston sets are supplied with high-strength piston pins and complete ring sets. Installation and drilling dimensions are of course included.
-
MAHLE Motorsport forged pistons for the highest demands!
With the high-performance pistons from MAHLE Motorsport for S65 V8 engines, you can easily reduce compression and achieve more power and durability. A special alloy and special ring zones ensure low running clearance and low blowby. This gives you the best tuning results and a lot of fun while driving!
Thanks to many years of experience in motorsport, MAHLE is one of the leading manufacturers of high-quality piston.
Features:
- Low running clearance possible thanks to special alloy
- Smooth engine running even in cold start phase
- High-performance piston pin
- Low blowby due to special ring zones
- Anti-friction graphite coating
- Mahle high-performance piston rings
- Extremely light with only approx. 360 g per piston
- Plug & Play installation possible
All piston sets are supplied with high-strength piston pins and complete ring sets. Installation and drilling dimensions are of course included.
-
Mahle Performance Piston kit for all BMW E46 M3 3.2L S54B32 engines.
These pistons are recommended for any high performance engine build, as they offer unparalleled strength and longevity.Features:
- original Mahle
- much lighter
- reinforced
- complete kit with rings and pins
- bore size 87.50mm ( OEM 87,00mm )
- compression 9:1 or 12,3:1
- 21mm piston pin diameter
- Durable forged pistons
- Lightweight piston design
- High strength German steel wrist pins for high horsepower support
- Propriety Mahle low-expansion 142P alloy
- Tight ring to piston groove clearances to reduce blow-by
- Hard anodized ring lands to avoid micro-welding
- Grafal anti-friction skirt coating
- Oil squirter notches that ensure no piston skirt to squirter interference
For following BMW E46 M3 engines with engine code S54B32.
To maximize power output, the clearances between the rings and piston have been brought in very tightly to reduce blow by. This is achieved by hard anodizing the top ring lands, which prevents micro welding which could be caused otherwise.
To maintain OEM-like wear characteristics, these pistons are coated with Mahle’s Grafal skirt coating. This coating reduces friction on the skirts, keeping them quiet and from wearing over time- extending piston life. The grey appearance of these pistons is due to a phosphate coating. Providing a lubricant film in the pin bores and ring grooves, this coating is essential for initial startup and break-in of the engine to prevent micro welding and galling. Features like these are what allow these pistons to last for thousands of miles, just like OEM units. -
Forged high-performance pistons from Mahle Motorsport for your BMW E80, E90, E89 and F01 3.0L 24V engines with the engine code N54B30 as in the 135i, 335i, 740i and z4 35i.
A special alloy and special ring zones ensure a low running clearance and a low blowby. This will give you the best tuning results and a lot of driving fun!
features:
- Extremely light due to special alloy
- Reinforced for maximum performance
- 22mm piston pin
- Anti-friction graphite coating
- Complete set incl. Piston pin, rings and clips
- Installation and drilling dimensions are included
- The specified compression is in conjunction with a standard cylinder head gasket.
Since the standard conrods are not able to perform 500 hp or more, we recommend strong H-shaft conraods.
(picture similar)
-
Forged high performance pistons made by Wössner for the S54B32 engines with 21mm piston pin as in the E46 M3 or Z4 M Coupe
Innovative specialists for high performance pistons. Wössner pistons work in engines at the highest level of motorsport, as well as in everyday use - wherever performance and longevity are very important factors.
features:
- Original Wössner
- MADE IN GERMANY
- Compaction 12.3:1
- Extremely light, only about 316g per piston
- Reinforced for maximum performance
- 21mm piston pin
- Piston skirt coated for less friction
- Installation and drilling dimensions are included
Wössner pistons are supplied with the corresponding piston rings, piston pins and securing clips
Picture similar
-
High Performance Pistons from WISECO for BMW M54B30 3.0L 24V Double Vanos engines.
Features:
- original Wiseco
- much lighter
- reinforced
- complete kit with rings and pins
- also for OEM bore size available 84,00mm
- 22mm piston pin diameter
- skirt coated for less friction
The specified compression is based on a 0,70mm head gasket.
The picture is similar. -
High Performance Pistons from WISECO for BMW 3.2l 24V S54B32 engines.
Features:
- original Wiseco
- much lighter
- reinforced
- complete kit with rings and pins
- also for OEM bore size available 87,00mm
- 21mm piston pin diameter
- skirt coated for less friction
The specified compression is based on a 0,64mm head gasket.
The picture is similar. -
High Performance Pistons from WISECO for BMW M50B25 2.5L 24V engines.
Features:
- original Wiseco
- much lighter
- reinforced
- complete kit with rings and pins
- also for OEM bore size available 84,00mm
- 22mm piston pin diameter
- skirt coated for less friction
The specified compression is based on a 1,75mm head gasket.
The picture is similar. -
High Performance Pistons from WISECO for M50B30 and S50B30 3.0L 24V engines by BMW.
Features:
- original Wiseco
- much lighter
- reinforced
- complete kit with rings and pins
- also for OEM bore size available 86,00mm
- 21mm piston pin diameter
- skirt coated for less friction
The specified compression is based on a 1,74mm head gasket.
The picture is similar. -
High Performance Pistons from WISECO for BMW M52B25 2.5L 24V Single Vanos Turbo engines.
Features:
- original Wiseco
- much lighter
- reinforced
- complete kit with rings and pins
- also for OEM bore size available 84,00mm
- compression 8.8:1 for Turbo
- 22mm piston pin diameter
- skirt coated for less friction
The specified compression is based on a 1,75mm head gasket.
The picture is similar. -
High Performance Pistons from WISECO for S50B32 3.2L 24V BMW engines.
Features:
- original Wiseco
- much lighter
- reinforced
- complete kit with rings and pins
- bore size available 86,50mm upward
- 21mm piston pin diameter
- skirt coated for less friction
The specified compression is based on a 1,75mm head gasket.
The picture is similar. -
Forged high performance pistons from WISECO for all BMW M20B25 2.5L 12V engines.
Features:
- Original Wiseco
- Extremely light due to special alloy
- Reinforced for maximum performance
- High strength material, therefore also suitable for turbo
- Also for series bore 84,00mm
- 22mm piston pin
- Piston skirt coated for less friction
- Complete set incl. piston pin, rings and clips
- Installation and drilling dimensions are included
For BMW M20B25 2.5L 12V engines.
The specified compression is in conjunction with a 1.75mm cylinder head gasket.
We additionally recommend either using the stock connecting rods with ARP connecting rod bolts or converting directly to H-Beam conrods.
Image similar. -
High Performance Pistons from WISECO for BMW M50B25 2.5L 24V Single Vanos engines.
Features:
- original Wiseco
- much lighter
- reinforced
- complete kit with rings and pins
- also for OEM bore size available 84,00mm
- 22mm piston pin diameter
- skirt coated for less friction
The specified compression is based on a 1,75mm head gasket.
The picture is similar. -
High Performance Pistons from WISECO for BMW 3.6L 24V S38B36 engines.
Features:
- original Wiseco
- much lighter
- reinforced
- complete kit with rings and pins
- bore size available 94,00mm upward
- 22mm piston pin diameter
- skirt coated for less friction
The specified compression is based on a 1,75mm head gasket.
The picture is similar. -
High Performance Pistons from WISECO for BMW 3.8L 24V S38B38 engines.
Features:
- original Wiseco
- much lighter
- reinforced
- complete kit with rings and pins
- bore size available 95,00mm upward
- 22mm piston pin diameter
- skirt coated for less friction
The specified compression is based on a 1,75mm head gasket.
The picture is similar. -
High Performance Pistons from WISECO for BMW 2.0L 8V M10B20 engines.
Features:
- original Wiseco
- much lighter
- reinforced
- complete kit with rings and pins
- also for OEM bore size available 89,00mm
- 22mm piston pin diameter
- skirt coated for less friction
The specified compression is based on a 1,52mm head gasket.
The picture is similar.
Технически характеристики
Общи данни
Система за гориво
Контролни стойности за изгорелите газове
Данни за ходовата част
Спирачна уредба
Електроника
Консумативи
Осветление
Интервали за смяна
-
Огромен избор Над 800 000 авточасти
-
Купи на кредит с ТБИ Минимална сума 150 лв.
-
Експресна доставка Наложен платеж и преглед
-
14 дни срок Връщане или замяна
ТОП производители
